Wednesday, January 11, 2006

Base Interior

Rear firewall, tunnel and floorFront firewall, tunnel and floor. That is not my steering wheel. It is just a dummy for positioning purposes. We're going to have one like the original.New dash

Tuesday, January 10, 2006

New Equipment

Steering shaft, brake master cylinder, firewall, and dummy engineAldan shocks and 2.5" x 9" coilover springs. Wilwood brake disk and 6 piston calipers.Power assist steering rack and dummy engine.

Rear Suspension

Here's a closer look at the modified four-link suspension. I know it is much more archaic than the original hydropneumatic independent suspension. But it can handle the added power without any additional engineering. Keep in mind that the original was front wheel drive. The rear suspension arms would have needed reworking to accept drivelines. And there was an engineering question about how those arms would accept the additional loads coming from the drivelines.I think the ideal solution would have been to make an independent rear suspension using unequal A-arms, coil-overs and differential from a corvette. Then at some later date, when I find an open-minded Citroen expert, I could have the hydropneumatic system reinstalled. By that I mean put in the tank, pump, main accumulator, suspension control valves, suspension pressure spheres, and height correctors. Then I would remove the coilover springs and substitute pushrods and pivots that would run to the pressure spheres.


Independent Front Suspension

Here is a better look at the Mustang II geometry independent fron suspension.

New Chassis

The new frame is simple ladder of box section tubes.It includes Mustang II style independent front suspension.The rails needed to be shortened by about six inches at the rear cross member to fit.It also includes a solid rear axle and modified four-link rear suspension.More of the trunk rust is evident here.

Rust Repair

New sheet metal was fabricated to replace part of the trunk support.and to replace the rocker panels on both sides.

Monday, January 09, 2006

Rust

The rocker panels were completely rusted out. As were the bottoms of the doors


The trunk supports
The C pillar
The other C pillar and rain gutters
and more issues with the trunk support.

Deconstruction

It starts...

...and ends...You can see we didn't save much. We kept the body panels and this supporting framework. It is getting an all new chassis, running gear and interior.

Kevin Bradley

I talked to a local hot rod builder who specializes in '32 Fords, Vern Tardell. I guess he's actually kind of famous. He thought it was an interesting idea but he didn't want to do it.

Then I was browsing at a hot rod show in Fortuna, California when I ran into Kevin Bradley, a hot rod builder from that area. I told him about my idea. He thought it sounded fun. I checked out his operation and some other cars he had done. He took a look at my car. He told me his ideas and made a proposal. We made a deal. He took the car to Rio Dell and got started.

For cost reasons, I made two compromises, that I am still conflicted about. I agreed to use a solid rear axle instead of independent rear suspension. And I agreed to give up the Citroen hydropneumatic springing and ride leveling system.

I gave up the independent rear suspension on the theory that I will use the car as a family-type cruiser rather than a road racer. We could have used a modified corvette-type independent rear suspension but that would have added quite a bit to the cost. I gave up the hydropneumatic springing and ride levelling system for several reasons. Kevin had no experience with it (who does?), our rebuilt version of the car is heavier than the original, we'd given up the independent rear anyway, and if I really wanted to I could use air-ride springs.

The Dream

First, I thought I would restore it myself. How hard can it be? Then I realized it wasn't an issue of difficulty but an issue of patience. I found I lacked patience. Next, I thought I would pay someone to restore it. Then I learned what many have learned before, it is cheaper to buy a pristine example then to pay for a restoration. I had a dilemma. I wanted to have this car and drive it but it made no economic sense to restore it to original. And if I was going to pay too much money for something there were some things I would change. Like, I'd want more power. How about 400 horsepower instead of the 88 original horsepower? And air conditioning; I need air conditioning. It's probably not very safe the way it is. Can I improve the safety features; maybe strengthen the passenger compartment somewhat? One thing led to another.

This is where it finally ended up. I spec'd a 400+ horsepower corvette crate engine, an appropriate transmission, rear wheel drive instead of the existing front wheel drive, beefed up independent suspension and brakes all around, and a new interior. Basically I wanted a new car with the old body.